Questions and answers about PRODUCTS – Page 4

This forum contains 97 topics and 227 replies, and was last updated by plenumtechnologies12 5 days, 9 hours ago.

Viewing 22 topics - 76 through 97 (of 97 total)

← 1 … 3 4

- Topic
- Voices
- Posts
- Freshness
- NCS314: What does the Variable Resistor adjust?
  Started by: Ric
- 2
- 2
- 5 years, 5 months ago
  Gra Afch
- NCM109 Night Mode
  Started by: Kordus
- 2
- 3
- 5 years, 6 months ago
  Kordus
- Help — NC314 2.2 starts up, but no tubes
  Started by: derek.merck
- 3
- 4
- 5 years, 7 months ago
  billymac101
- NCS314 Shield – L1 getting VERY hot
  Started by: buildxyz
- 2
- 2
- 5 years, 7 months ago
  Gra Afch
- Nixie clock error?
  Started by: Marcel Alfonsi
- 2
- 2
- 5 years, 7 months ago
  Gra Afch
- Disable audio
  Started by: edwinelisia
- 2
- 2
- 5 years, 7 months ago
  Gra Afch
- How to disable the separator dots
  Started by: carlosb
- 2
- 3
- 5 years, 9 months ago
  carlosb
- 1K Revision
  Started by: scottle
- 2
- 5
- 5 years, 9 months ago
  scottle
- IN-18 – 4 Tubes
  Started by: scottle
- 2
- 2
- 5 years, 10 months ago
  Gra Afch
- Board wont power on
  Started by: zack3Dprints
- 2
- 3
- 5 years, 10 months ago
  zack3Dprints
- Nixies won't light up and Q1 overheating
  Started by: goldengaming12
- 2
- 2
- 5 years, 10 months ago
  Gra Afch
- Tube display seems out of order
  Started by: james.hilferty
- 2
- 5
- 5 years, 11 months ago
  james.hilferty
- How to deactivate slot machine effect
  Started by: Gra Afch
- 1
- 1
- 5 years, 11 months ago
  Gra Afch
- TLS connector at NCM109 v.1.1 board
  Started by: Jukka
- 2
- 2
- 5 years, 11 months ago
  Gra Afch
- Can't upload arduino sketch to nixie clock
  Started by: nixmix
- 3
- 6
- 5 years, 11 months ago
  Gra Afch
- Missing or low voltage at point TP4
  Started by: Gra Afch
- 3
- 4
- 5 years, 11 months ago
  yaelblaze
- Only 11,45v on TP2
  Started by: jeroen
- 3
- 7
- 5 years, 11 months ago
  yaelblaze
- PIR Sensor / Switch ON/OFF
  Started by: ARNAUD.DAVID
- 3
- 3
- 5 years, 11 months ago
  Zwartoog
- JST connector next to IR receiver
  Started by: Zwartoog
- 1
- 1
- 6 years, 2 months ago
  Zwartoog
- Use of SPI1 connector on bottom of NCS314 Shield?
  Started by: sutton57
- 2
- 2
- 6 years, 4 months ago
  Doridian
- Using PWM to dim NCS314 bulbs
  Started by: sutton57
- 2
- 2
- 6 years, 4 months ago
  Doridian
- Will Bare Nixie Tube PCB Arduino Shield work with Arduino Mega 2560 Rev3?
  Started by: andrew.plaza
- 2
- 2
- 6 years, 6 months ago
  Gra Afch

Viewing 22 topics - 76 through 97 (of 97 total)

← 1 … 3 4

You must be logged in to create new topics.

Cart